Wedding diadem

Difficulty: 3
Technique: Stringing, Wirework

Seed bead headband

This original headband made with seed beads from the PRECIOSA Traditional Czech Beads™ brand consists of two sizes of rocailles and the two-hole PRECIOSA Twin™ seed bead. The selection of seed beads in the color combination of crystal with a silver lining and white chalk with lustres predetermines its use on special occasions.

Ambassadors

Helena Chmelíková

She is able to switch from luxurious and extravagant fashion show pieces to the preparation of hobby projects,

Learn More

Materials & Tools

Other materials & tools

A headband hoop (a flat profile, round), a thin 0.35mm wire – surface finishing: silver or platinum, snipping pliers, flat nosed pliers

Procedure

Step 1

First prepare the circumferential band. Alternately string 1x T and 1x R10 onto the wire (designate the length according to the length of the band and add ca 10 cm). Add 3x R10 between both holes of the T at the end of the band at the turn. Continue stringing the T and R10 until both ends of the wire meet. Cross them and twist them several times and hide about 1 cm between the bandand the hoop. Do not fully tighten the band completely, the wire will be needed when connecting it to the hoop. You need 59x T to create the band. 

1

Step 2

Place the band on the centre of hoop and wind it around the outer seed beads several times. Hide the short end of the wire between the hoop and the band. Pass the long end of the wire under the outer wire at the beginning of the band. Pull it in. Repeat the same on the opposite side of the hoop at the band’s second outer wire at the same place. Pass over 2x T (leave one gap) and repeat the attachment. Once again pass over 2x T and continue to the end of the band. In order to affix the edge of band, twist the wire around the outer seed beads, pass the wire under the band and snip it off.

Step 3

Form the arches. Prepare three wires (designate the length according to double the length of the curve and add ca 10 cm). Count out 29x T from the band and pull the centre of the wire from them under the two T on both sides. Alternately string the T and R10 on the wire similarly as in the case of the band. Leave out several R10 on the inner side of the curve which will help to form it. Twist the end of the wire around the hoop under the band. Start the smallest arch at the foot of the biggest arch and twist the end of the wire at the centre of the headband. The biggest arch requires 28x T, the central arch requires 18x T and the small arch requires 14x T. The ending: the biggest and central arches 15x from the beginning and the small one 25x from the beginning of the band. The beginning: the largest arch 27x from the beginning, the central one 29x from the beginning and the smallest arch 17x from the beginning of the band.

3

Step 4

Attach the 6 stems with seed beads between the two arches in the centre of the headband. Cut off about 1 m of wire. String 1x R4 in the centre. Cross the wire and wind it several times. String another 1x R4, the distance of the placement of the R from the end of the already completed stem is the approximate length of the new stem. Fold the wire and twist. Proceed in the same way with the other stems. After completing all six of the stems, twist the end of the wire around the hoop. The length of the stems is 6 - 8 cm. Use the short wire to attach the stems between the arches. Form smaller 3 - 4 cm long stems at the edges behind the arches.

4

Step 5

Make the flowers on the top arches. Use about 60 cm of wire and place it in the middle. Start making the flower in the first half of the wire. String 10x T and twist the wire several times. String the central R4 and 1x T and pass the second end of the wire through the second hole of the T. Also pass it through all the second holes of the T and twice in the first T (do not tighten). Affix to the arch and continue to the second flower. On the way, strengthen the 4 stems by means of simple winding. String 10x T and create a ring. Add the central R4, pass the wire between the opposite seed beads and into the second hole of the T. Also pass it through all the second holes of the T and twice in the first one (do not tighten). Attach the end of the wire to the arch. Add the central flower between the arches. Make it in the same way as the first one above the arch. Continue to the flowers at the ends of the headband behind the arches. Make them in the same way as the arches; only leave out the part with the stem windings. Attach the end of the wire to the arch and to the band.

5 / a

Downloads

This website is using cookies

To improve our services and provide information that suits your interest, we use the advanced website traffic analytics tools. However, we need your consent. More information about how we process and protect your data can be found in the privacy statement. We ask you for approval of the terms.

Functional cookies These cookies are necessary for the proper functioning of the website and therefore cannot be turned off.
Analytics cookies Analytical cookies help us track and analyze the way visitors interact with our site in Google Analytics 4. This information allows us to improve content and provide a better user experience.
Marketing cookies Reading and writing cookies for marketing purposes for advertising systems such as Google Ads or Sklik. These cookies allow us to track user behavior and measure website performance and the effectiveness of our advertising campaigns.
Personalized advertising Remarketing cookies allow us to present you with personalized advertising based on your previous interactions with our site in systems such as Google Ads, Sklik.
Use of personal data With this option, you consent to the sending and processing of your personal data to Google for the purposes of targeting and evaluating online advertising and targeted marketing.