Shadows of the Rain Forest

Difficulty: 2
TECHNIQUE: a connected stringing (the right angle stitch)

Distinctive bracelet made from PRECIOSA Tubes

Be inspired by the color pallet of the warm months of the year. Make a bracelet according to the accessories that are trending in 2021. Play around with PRECIOSA Tubes in the tones of dark shadows, reflections from the water's surface and the rustling of leaves. You are sure to be pleased with the result.

Ambassadors

Helena Chmelíková

She is able to switch from luxurious and extravagant fashion show pieces to the preparation of hobby projects,

Learn More

Procedure

The length of the assembled bracelet is about 17.5 cm. You can adjust the length as required; finish the stringing earlier or otherwise extend it. Always finish the shorter sides with a T2. You can create your own color mix from the T1. It is possible to change the number of shades. The bracelet consists of four interconnected parts, each strung on about 1.10 m of wire. The edges are glued into the clasp.

Step 1

Cut off about 1.10 m of wire. String 2x T2 onto it. Move them into the middle of the wire. Thread one end of the wire through 1x T2 one more time. Always tighten the wire gently, but firmly.

1 / a

Step 2

String 1x T1 onto one end of the wire. Also thread the second end of the wire through the T1. At the same time, reinforce them by gently threading the wire through the T2 and T1 again.

2 / a

Step 3

String 6x R and 1x T1 onto one end of the wire. Also thread the second end of the wire through the T1.

3 / a

Step 4

String 1x T1 onto one end of the wire. Also thread the second end of the wire through the T1.

4 / a

Step 5

String 6x R and 1x T1 onto the opposite end of the wire than in Step 3. Also thread the second end of the wire through the T1.

5 / a

Step 6

String 1x T1 onto one end of the wire. Also thread the second end of the wire through the T1.

6 / a

Step 7

Continue until the wire is used up (don't forget the tightening of the knot). Alternate Steps 3 and 5. Add 1x T1 between them as in Step 4. Tie off the ends of the wire with two knots.

7 / a

Step 8

Thread a new wire through the last T1 from Step 7. Move it to the centre of the wire. Continue according to Steps 3, 4, 5 and 6.

8 / a

Step 9

The bracelet is edged with 18 arches along the longer sides (9 on each side). The shorter sides are completed with 2x T2. Don't forget to sew in the last T1 and the following T2 one more time. Pull the ends of the wire into the nearest T1 or T2. Put both ends of the wire from the same knot into the same T1 or T2. Snip off any protruding ends of the wire.

9 / a

Step 10

Apply the glue to the hollow in the clasp. Insert the outer T2. Hold it or secure it in place until the glue dries.

10 / a

Downloads

This website is using cookies

To improve our services and provide information that suits your interest, we use the advanced website traffic analytics tools. However, we need your consent. More information about how we process and protect your data can be found in the privacy statement. We ask you for approval of the terms.

Functional cookies These cookies are necessary for the proper functioning of the website and therefore cannot be turned off.
Analytics cookies Analytical cookies help us track and analyze the way visitors interact with our site in Google Analytics 4. This information allows us to improve content and provide a better user experience.
Marketing cookies Reading and writing cookies for marketing purposes for advertising systems such as Google Ads or Sklik. These cookies allow us to track user behavior and measure website performance and the effectiveness of our advertising campaigns.
Personalized advertising Remarketing cookies allow us to present you with personalized advertising based on your previous interactions with our site in systems such as Google Ads, Sklik.
Use of personal data With this option, you consent to the sending and processing of your personal data to Google for the purposes of targeting and evaluating online advertising and targeted marketing.