Wedding Belles

Difficulty: 2
TECHNIQUE: Herringbone stitch and basic wirework

Seed Bead Collection

Follow this tutorial to make simple bell-shaped flowers using pretty PRECIOSA Pearl Pastel Lining seed beads. Create an elegant necklace by attaching a cluster of flowers to delicate silver chain, or build a collection of romantic pieces suitable for the bride and her bridesmaids.

Ambassadors

Kerrie Slade

Kerrie Slade have used Czech PRECIOSA Traditional Czech seed beads in her creation.

Learn More

Material and Tools

Procedure

The finished necklace measures approximately 50 cm.

Step 1

To make the first flower:

Thread your needle with 1.1 m of thread and pick up 6x R10A. Leaving a 40 cm tail, pass your needle through all the R10As a second time to form a ring and then pass through the first R10A again. Figure 1.

1

Step 2

Add 1x R10A between each R10A added in the previous step and complete the row by stepping up through the first R10A of this row. Figure 2.

2

Step 3

Add 2x R10A between each R10A added in the previous step and complete the row by stepping up through the first R10A only of this row. Figure 3.

3

Step 4

Working in herringbone stitch, pick up 2x R10A and pass your needle down the next R10A in the previous row and up the next R10A. Continue in this way adding a total of 6 pairs of R10As and complete the row by stepping up through the first R10A only of this row. See Figure 4.

4

Step 5

Following step 4, work another 5 rows of herringbone stitch, adding 12x R10A per row and completing each row by stepping up through the first R10A only of each row. Pull your thread firmly as you work and encourage your work to form a tube. Figures 5a and 5b.

5 / a

Step 6

Work a single increase row by adding 2x R10A onto each pair added in the last row of the previous step and 1x R10A between each pair. Complete the row by stepping up through the first R10A only of this row. Figures 6a and 6b.

6 / a

Step 7

Pick up 3x R10A and pass your needle down 2x R10A instead of the usual 1, through the single increase bead added in the previous step and up the next 2X R10A. Continue in this way adding a set of 3x R10A onto each pair added in the previous step. Complete the row by stepping up through the first 3x R10A of this step only and tie off and trim the working thread. Figures 7a and 7b.

7 / a

Step 8

Thread your needle onto the tail thread and pass through the central hole to exit the inside of the flower. Pick up 8x R6A and 1x R10B and pass your needle back through the 8x R6A and back through the central hole to exit the top of the flower. Figure 8a. Pick up 1x R6B and pass through the central hole, through the 8x R6A and the R10B and back through the R6A and the central hole again. Figure 8b. Retrace the thread path twice more to strengthen the central stamen and then tie off and trim the thread. Figure 8c.

8 / a

Step 9

To make the necklace:

Following steps 1 – 8, make a total of 16 flowers. Make 4 using R10A - 4 with R10B, 4 with R10C and 4 with R10D. Vary the colour of the central stamen using R6 in colours A, B, C and D. For the R10 at the bottom of the stamen, work in the same colour as the stamen. For the R6 at the top of the flower, work in the same colour as the flower.

Step 10

Using your wire cutters, cut 17 links of chain. Open a jump ring with the pliers and pass it through the R6 on top of one of the flowers and through a link at one end of the chain. Close the jump ring. Figure 10.

10

Step 11

Repeat step 10 to add one flower to each chain link, leaving the top link empty. Figure 11.

11

Step 12

Cut a 48 cm length of chain, find the centre link and attach a split ring to it. Using the jump rings and working out from the centre of the necklace, add 1x R6 to every fifth link along both sides of the necklace. Figure 12.

12

Step 13

Attach 1x split ring to either end of the necklace and add the clasp to one of the split rings. To create the extension chain, add the charm to a split ring and attach it to one end of the small remaining section of chain. Attach the other end to the split ring at the end of the necklace. Figure 13.

13

Step 14

Connect the cluster of flowers to the necklace by attaching the empty link to the split ring at the centre of the necklace. Figure 14.

14 / a

Downloads

This website is using cookies

To improve our services and provide information that suits your interest, we use the advanced website traffic analytics tools. However, we need your consent. More information about how we process and protect your data can be found in the privacy statement. We ask you for approval of the terms.

Functional cookies These cookies are necessary for the proper functioning of the website and therefore cannot be turned off.
Analytics cookies Analytical cookies help us track and analyze the way visitors interact with our site in Google Analytics 4. This information allows us to improve content and provide a better user experience.
Marketing cookies Reading and writing cookies for marketing purposes for advertising systems such as Google Ads or Sklik. These cookies allow us to track user behavior and measure website performance and the effectiveness of our advertising campaigns.
Personalized advertising Remarketing cookies allow us to present you with personalized advertising based on your previous interactions with our site in systems such as Google Ads, Sklik.
Use of personal data With this option, you consent to the sending and processing of your personal data to Google for the purposes of targeting and evaluating online advertising and targeted marketing.