Scales

Difficulty: 2
Technique: stringing

Distinctive bracelet made from PRECIOSA Engraved Pip

We have prepared a new PRECIOSA Engraved Pip bead for you, the shape of which is based on the classic PRECIOSA PipTM bead. You are sure to appreciate the distinctive embossed line that is reminiscent of the venation of leaves or the patterns on the scales of fish or lizards. Choose from the wide range of varied finishes.

Ambassadors

Helena Chmelíková

She is able to switch from luxurious and extravagant fashion show pieces to the preparation of hobby projects,

Learn More

Material and Tools

Materials

Caps (14 x 14 mm); a large carabiner; a metal crimp bead (CB); 8 mm and 6 mm rings; a thin 5 mm ring

Tools

A regular 0.38 mm wire; a 0.20 mm nylon line; a thin needle; scissors; snipping pliers; flat-nose pliers (for handling the rings and the CB)

Procedure

Step 1

String 3x P onto the line. Thread the line through them one more time. Tighten it. Tie two knots. Pull the ends into the two holes and cut them off.

1 / a

Step 2

You need 24 cornets with three leaves.

2

Step 3

Cut off 50 cm of wire. String 1x CB, 1xs R8, 1x CB, 1x R8 and the cap through the dimpled side. Continue by stringing 8x R15. Return the wire to the cap. This will create a loop of R15. Also thread it through the R8 and the CB.

3 / a

Step 4

Grip the CB close to the dimple using the flat-nosed pliers. Move it in as deeply into the dimple as possible and crimp it. Do the same with the second CB.

4 / a

Step 5

String the cornet through the pointed end. Add 1x R10 and 1x R8 to it. Repeat this a total of 24x. Start stringing on the short and long ends of the wire. Then only work on the long end.

5 / a

Step 6

Instead of the last R8, string 2x CB, 1x FPB, 3 more R8, a cap from the dimple and 8x R15. Return the wire to the cap. This will create a loop. Also thread it through the R8, FPB, CB, several cornets and the R10 and R8 between them.

6 / a

Step 7

Cut off the wire. Crimp 2x CB. Hold the end of the wire. Cut off the protruding section.

Step 8

Make an adjusting chain from the 8 mm rings. String two rings onto the loop of R15 and close them. Connect two new rings to these two. Repeat this 6 more times (a total of 8x). Thread the thin 5 mm ring through the hole in the P and connect it to the outer rings.

8 / a

Step 9

Attach the carabiner to the second loop of R15 using a 6 mm ring.

9 / a

Downloads

This website is using cookies

To improve our services and provide information that suits your interest, we use the advanced website traffic analytics tools. However, we need your consent. More information about how we process and protect your data can be found in the privacy statement. We ask you for approval of the terms.

Functional cookies These cookies are necessary for the proper functioning of the website and therefore cannot be turned off.
Analytics cookies Analytical cookies help us track and analyze the way visitors interact with our site in Google Analytics 4. This information allows us to improve content and provide a better user experience.
Marketing cookies Reading and writing cookies for marketing purposes for advertising systems such as Google Ads or Sklik. These cookies allow us to track user behavior and measure website performance and the effectiveness of our advertising campaigns.
Personalized advertising Remarketing cookies allow us to present you with personalized advertising based on your previous interactions with our site in systems such as Google Ads, Sklik.
Use of personal data With this option, you consent to the sending and processing of your personal data to Google for the purposes of targeting and evaluating online advertising and targeted marketing.