Creole

Creole

Earrings made from wire memory wire using PRECIOSA Candy™

PRECIOSA ORNELA presents the PRECIOSA Candy™ low cabochon with a round 8 mm base. The shallow rounding in the lower section means that it can be easily sewn around,joined with other beads of the same type or combined with other bead types.

Design: Helena Chmelíková

Choose from the rich range of half and full coatings on this new two-hole PRECIOSA Candy™ bead. Make use of the creative possibilities presented by the low two-hole cabochons, supplement them with PRECIOSA rocailles in suitable Sol-gel colors and create the elegant Creole earrings.


icon pdf downloadDownload the project in PDF file format


Materials and tools:

The green variant

PRECIOSA CandyTM (C)
111 01 363; 8 mm; 02010/25034; 28x

kreole candy zelena varianta x

PRECIOSA Rocailles (R10)
331 19 001; 10/0; 02654; 228x

kreole rokajl zelena varianta

The pink variant

PRECIOSA CandyTM (C)
111 01 363; 8 mm; 02010/15696; 28x

kreole candy ruzova varianta

PRECIOSA Rocailles (R10)
331 19 001; 10/0; 78691; 228x

kreole rokajl ruzova varianta

The grey variant

PRECIOSA CandyTM (C)
111 01 363; 8 mm; 23980/14400; 28x

kreole candy seda varianta

PRECIOSA Rocailles (R10)
331 19 001; 10/0; 02641; 228x

kreole rokajl seda varianta

The purple-black variant

PRECIOSA CandyTM (C)
111 01 363; 8 mm; 23980/23001; 28x

kreole candy fialovoerna varianta

PRECIOSA Rocailles (R10)
331 19 001; 10/0; 01623; 228x

kreole rokajl fialovocerna varianta
kreole obr 5c kreole ruzova varianta kreole seda varianta x kreole fialovocerna varianta

or any other shades of PRECIOSA CandyTM and PRECIOSA Rocailles
- steel memory wire with a 6 cm wind diameter; 4 – 5 mm rings; earrings hooks
- large snipping pliers; pliers with a round point; flat nose pliers

kreole material

The procedure:

Step 1:
Snip off 2 pieces of memory wire, approximately one turn plus 4 cm (fig. no. 1). Make a loop on one end (fig. no. 2). Grasp the end of the memory wire between the rounded points of the pliers in the upper second. Twist the wire around the point. Gently remove the wire from the point with the twisted loop. The centre of the loop should be placed above the continuation of the wire. The loop should be twisted vertically.

fig. no. 1

kreole obr 1a x

fig. no. 2

kreole obr 1b

Step 2:
String 22 R10 on one wire (fig. no. 3). Alternately string 1 C and 1 R10 (fig. no. 4). String 14 C and 13 R10 (fig. no. 5). String another 22 R10 after the last C. Bend the free end of the memory wire with the flat nose pliers (fig. nos. 6, 7). Secure the R10 so that they do not fall off.

fig. no. 3

kreole obr 2a x

fig. no. 4

kreole obr 2b x

fig. no. 5

kreole obr 2c x

fig. no. 6

kreole obr 2d e

fig. no. 7

kreole obr 2f x

Step 3:

String 22 R10 onto the second wire (fig. no. 8). Thread the wire through the free holes in the C on the first wire. String 1 R10  between the C (fig. nos. 9 and 10). String another 22 R10after the last (fig. no. 11). Bend the free end of the memory wire with the pliers (fig. no. 12).

fig. no. 8

kreole obr 2a x

fig. no. 9

kreole obr 3b x

fig. no. 10

kreole obr 3c

fig. no. 11

kreole obr 3d x

fig. no. 12

kreole obr 3e

Step 4:
Tighten the stringing of R10 and C. Move the R10 and the C on the wire in the direction of the loops. Cut off the end of one wire bent with the flat nose pliers about 8 – 10 mm from the R10. Make a loop. The loop should also be placed vertically. Snip the second wire and then make a loop on it (fig. no. 13). If the adjacent ends of the wire cover one another after the loops have been created, try to carefully expand the circle (pull the ends of the wire from each other). The wire diameter will then be bigger.

fig. no. 13

kreole obr 4a

kreole obr 4b x

Step 5:
Thread 1 ring through two end loops. Open the loop on the earring hook. Thread it onto the ring and close it (fig. no. 14).
You now have one earring. Create the second one in the same way (fig. no. 15).

fig. no. 14

kreole obr 5b

fig. no. 15

kreole obr 5c

kreole bkreole a

kreole titulka ckreole titulka x