Floral Romance

Difficulty: 3
Technique: Beadweaving

Headband with Ribbon

The headband consists of a sewn lacy band and a ribbon which is tied under the hair. The lacy band consists of five identical repeating motifs and it consists of three fragments. Everything is sewn together and connected. One larger flower is omitted in the fifth outer section. A bracelet could also be made in the same way. In this case, only three of the lacy motifs would be repeated. We have selected a refined creamy color for our headband which can therefore be a suitable wedding accessory. The range of opaque and transparent colors of the glass or color finishes will enable you to give free reign to your creativity and to create your own color combinations. The headband can then suddenly become a flowering meadow of pastel colors. We wish you many creative ideas when working with Czech beads and seed beads from the PRECIOSA Traditional Czech Beads brand™. 

Ambassadors

Helena Chmelíková

She is able to switch from luxurious and extravagant fashion show pieces to the preparation of hobby projects,

Learn More

Materials & Tools

Other materials & tools

A 0.20 mm line or nylon thread, a thin 0.24 mm wire, scissors, a long threading needle, flat nosed pliers, a 1 cm wide ribbon, 1 m long 

Procedure

Each of the five sections is sewn from one large flower, three smaller flowers, two outer leaves and a further two smaller flowers and two rocaille leaves. Start with three smaller flowers and their two leaves. Connect the fragment of two flowers and two leaves so that the point of the lower leaf is connected with the following larger lacy section. Sew the large flower and its protrusions last.

Step 1

Start with the three flowers and two leaves. String 8x T onto the needle with the fine line or the nylon thread, move them to the end of the line and tie them in a ring with a strong knot. Pass the line through the second hole of the first T in the initial ring and gradually pass it through all of the second holes and add 1x R between every T. Then add 3x R in front of the last T according to the drawing, pass the line through the penultimate R and the second hole of the first T once again and repeat the same again at the nearest R (figure no. 1). Start forming the next flower (figure no. 2). Alternately string 8x T and 8x R. Pass the linethrough through the second hole of the first T and tighten the strung Twin seed beads into flowers. Then add 3x R according to the drawing, pass the line through two R one more time and start the stringing of 12x Rfor the first leaf. Pass the line back through the eleventh R in the opposite direction. String a further 10x R and close the leaf. Pass the line through the first four R once again and add 3x R, close the ring made of 4x R and start stringing the third flower.

1

Step 2

String 1x T, 1x R and 1x T and connect the first flower by passing the line through the outer of the four protruding seed beads. Then alternately string 6x T and 6x R and pass the line through both the holes in the first T and all of the remaining second holes. After tightening the internal section of the flower, pass the line through the three T once again according to the drawing and through the outer hole of the nearestT and R so that you come to the edge of the flower and can string the seed beads connecting the flower to the second leaf. String 3x R and pass the line through these four R once again. String 12x R and pass the line through the eleventh R in the opposite direction. Then string 3x R and connect this leaf with the first leaf by passing the line through the four R from the first leaf according to the drawing. String 3x R, then pass the line through the 2 nearest R, tighten the strung beads commensurately, straighten the entire motif of three flowers and two leaves and close with a knot and hide the end of the line in the hole of the following seed bead. 

2 / a

Step 3

The second motif consists of two flowers and two leaves. Proceed similarly to as in the first motif. Create a flower from 8x T, add a total of 8x R to the outer circumference between the individual T. Add another 3x R at the penultimateT and connect the flower with the first leaf of the previous motif. Complete the flower, pass the line through the second hole of the first T and the first added R one more time, add 3x R, pass the line through 2x R one more time, tighten the connecting element and start the stringing of the new leaf. String 12x R and pass the line back through the eleventh R, add 10x R and complete the leaf. 

3

Step 4

Pass the line through the five R again, add 3x R and create a further connecting element to connect the new flower. Alternately string 8x T and 8x R to create the next flower. Add another 1x R after the second R, create another connecting element and connect the newly created flower with the second leaf of the previous motif, add 1x R, pass the line through the second R of the flower once again and complete with an alternating stringing of T and R. Pass the line one more time through the first T and pass the line through all the internal holes and tighten the internal section of the flower. Pass the line out from the inside of the flower through the outer hole of the penultimate T and R add 13x R and pass the line through the penultimate R in the opposite direction. String 3x R, pass the line through four R from the previous leaf. Add 3x R, pass the line through the four R in this line, add 1x R, pass the line through the two R from the new leaf once again, tighten and straighten the entire motif, finish with a tight knot and hide the ends of the line in the surrounding holes and cut it. 

4

Step 5

Create a larger flower from 10x T and 10x R for the connection of the individual lacy flower motifs and connect the individual sections according to the drawing (figure no. 5a). Finish it off, clear away the line and cut it. The connection at the flowers is realised by adding 3x R in two places and at the leaves by adding a ring of 8x R. Pass the line through the outer R of the leaf at the end of the headband one more time and then finish. Attach a stringing of 21x R in a loop to the point of the leaf (figure no. 5b). Pass the thin line through all these R one more time, finish with a knot and hide the ends in the neighbouring holes. Connect another loop of 21x R on the other side of the headband using the connecting element made of 3x added R. Pass the ribbon, which is used to tie the headband below the hair, through both outer loops. 

5 / a

Downloads

This website is using cookies

To improve our services and provide information that suits your interest, we use the advanced website traffic analytics tools. However, we need your consent. More information about how we process and protect your data can be found in the privacy statement. We ask you for approval of the terms.

Functional cookies These cookies are necessary for the proper functioning of the website and therefore cannot be turned off.
Analytics cookies Analytical cookies help us track and analyze the way visitors interact with our site in Google Analytics 4. This information allows us to improve content and provide a better user experience.
Marketing cookies Reading and writing cookies for marketing purposes for advertising systems such as Google Ads or Sklik. These cookies allow us to track user behavior and measure website performance and the effectiveness of our advertising campaigns.
Personalized advertising Remarketing cookies allow us to present you with personalized advertising based on your previous interactions with our site in systems such as Google Ads, Sklik.
Use of personal data With this option, you consent to the sending and processing of your personal data to Google for the purposes of targeting and evaluating online advertising and targeted marketing.